矽酮膠是一種類似軟膏，一旦接觸空氣中的(de)水分就會固化成一種堅韌的橡膠類固體的材料。主要分為脫醋酸型，脫醇型，脫氨型，脫丙型。矽酮膠因為常被用于玻璃方面的粘接和密封，所以俗稱玻璃膠。Silicone rubber is a kind of ointment, once contact with moisture in the air will be solidified into a tough rubber type of solid materials.Mainly divided into the type of acetic acid, glycol type, ammonia, c.Because silicone rubber is often used for bonding and sealing glass, so commonly known as glass glue.
    單組份矽酮玻璃膠是一種類似軟膏，一旦接觸空氣中的水分就會固化成一種堅韌的橡膠類固體的材料。One-component silicone glass glue is a kind of ointment, once contact with moisture in the air will be solidified into a tough rubber type of solid materials.
    矽酮玻璃膠的粘接力強，拉伸強度大，同時又具有耐候性、抗振性，和防潮、抗臭氣和适應冷熱變化大的特點。加之其較廣泛的适用性，能實現大多數建材産品之間的粘合，因此應用價值非常大。Silicone glass glue stick relay is strong, tensile strength, and vibration resistance, weather and moisture, odor resistant and adapt to the characteristics of the change of hot and cold.Together with its broad applicability, which can achieve most adhesion between building materials products, so the application value is very big.
    矽酮膠英文名字是SILICONE，是有機矽部分産品. 主要分為脫醋酸型，脫醇型，脫氨型，脫丙型。玻璃膠是矽酮膠俗稱名稱，因為用戶購買矽酮密封膠主要使用于玻璃方面的粘接和密封，所以就叫做玻璃膠。Are English name is SILICONE, SILICONE rubber SILICONE products. Mainly divided into acetic acid type, type to take off the alcohol, ammonia, c.Glass rubber is a silicone rubber, commonly known as the name for the user to buy silicone sealant is mainly used in glass bonding and sealing, so he called the glass glue.
    化學成分有聚二甲基矽氧烷，二氧化矽的聚合物都可以稱矽酮。Chemical composition of polydimethylsiloxane, silicone polymer silica can say.
    矽酮的主要成分是聚二甲基矽氧烷，二氧化矽等組成。矽酮結構中矽和氧構成雙鍵的碳被矽代替。The main components of the silicone is polydimethylsiloxane, silica, etc.Silicone structure of silicon and oxygen by silicon instead of carbon double bond.
    就是這樣一個結構式，兩個矽酮可以發生聚合，斷掉一個矽氧鍵，Si原子再接一個基團，兩個氧連起來，就生成矽酮類物質。Is a structured, twosilicone can occur polymerization, breaking a silica key, Si atoms by another group, the two together, oxygen generates silicone material. 等元件的密封要良好，以防止空氣侵入，從而控制氣穴與氣蝕的發生。在開始運轉前，往齒輪泵的殼體内灌滿待輸送的液體，便于安全動。若環境溫度低于冰點，應預先向泵内通入熱蒸汽，進行預熱處理，然後才可啟動齒輪泵。齒輪泵的旋轉方向要與進、出油口相符。齒輪泵若是第一次運行，或長期閑置後再使用，最好在空載或小負荷情況下先跑合一小時左右。如果在跑合階段預先覺出異常溫升、洩漏、振動和噪聲時，應機檢查。高粘度泵的出口管路上還應當設置安全閥等保護裝置，這樣一旦泵的出口通道發生堵塞，就可以打開安全閥卸壓。對于需要正反轉的高粘度齒輪泵，其進出口管路上均需設置安全閥。High viscosity pump bearing or flange and its drive motor should use common installation basis, foundation, flange or support all needs to have enough rigidity, to reduce the vibration of gear pump is running and noise.Motor and gear pump with elastic shaft coupling, coaxial degree is less than 0.1 mm, Angle shall not be greater than 1 degree.When installing coupling hammer shall not be used, in order to avoid damage gear and other parts of the gear pump.If use the belt wheel, wheel, etc, shall set bracket support, in case of driving gear bearing by the radial force.Ground screw fastening gear pump, motor, screw force should be uniform, reliable connection.Turn the coupling with the hand, should feel can easily turn the gear pump, no abnormal phenomenon such as clamping, then can be piping.High viscosity gear pump oil suction pipe diameter should be large enough, and to avoid the narrow channel, or a sharp bend, bend, remove unnecessary valves, fittings, as much as possible to reduce the installation height of pump, shorten the length of the oil suction pipe, in order to reduce the pressure loss.Components, such as pipe joint sealed well, in order to prevent the air intrusion, thus control air-pocket and the occurrence of cavitation.Before starting operation, to gear pump casing filled with liquid, easy to safety.If the environment temperature is below freezing, should advance to pump into the hot steam, preheating treatment, and then to start the pump.Direction of rotation of the gear pump, oil outlet in accord.Gear pump is the first run, or long-term idle before using, had better under the condition of no load or small load to run one hour or so.If in the running-in stage in advance the abnormal temperature rise, leakage, vibration and noise, should machine inspection.High viscosity of the pump outlet pipe also shall set up relief valve or other protective device on the road, so that once the clogging pump export channels, can open the relief valve pressure relief.For high viscosity gear pump need positive &negative, import and export all needs to set up the line safety valve.等元件的(de)密封要良好，以防止空氣侵入，從而控制氣穴與氣蝕的發生。在開始運轉前，往齒輪泵的殼體内灌滿待輸送的液體，便于安全動。若環境溫度低于冰點，應預先向泵内通入熱蒸汽，進行預熱處理，然後才可啟動齒輪泵。齒輪泵的旋轉方向要與進、出油口相符。齒輪泵若是第一次運行，或長期閑置後再使用，最好在空載或小負荷情況下先跑合一小時左右。如果在跑合階段預先覺出異常溫升、洩漏、振動和噪聲時，應機檢查。高粘度泵的出口管路上還應當設置安全閥等保護裝置，這樣一旦泵的出口通道發生堵塞，就可以打開安全閥卸壓。對于需要正反轉的高粘度齒輪泵，其進出口管路上均需設置安全閥。High viscosity pump bearing or flange and its drive motor should use common installation basis, foundation, flange or support all needs to have enough rigidity, to reduce the vibration of gear pump is running and noise.Motor and gear pump with elastic shaft coupling, coaxial degree is less than 0.1 mm, Angle shall not be greater than 1 degree.When installing coupling hammer shall not be used, in order to avoid damage gear and other parts of the gear pump.If use the belt wheel, wheel, etc, shall set bracket support, in case of driving gear bearing by the radial force.Ground screw fastening gear pump, motor, screw force should be uniform, reliable connection.Turn the coupling with the hand, should feel can easily turn the gear pump, no abnormal phenomenon such as clamping, then can be piping.High viscosity gear pump oil suction pipe diameter should be large enough, and to avoid the narrow channel, or a sharp bend, bend, remove unnecessary valves, fittings, as much as possible to reduce the installation height of pump, shorten the length of the oil suction pipe, in order to reduce the pressure loss.Components, such as pipe joint sealed well, in order to prevent the air intrusion, thus control air-pocket and the occurrence of cavitation.Before starting operation, to gear pump casing filled with liquid, easy to safety.If the environment temperature is below freezing, should advance to pump into the hot steam, preheating treatment, and then to start the pump.Direction of rotation of the gear pump, oil outlet in accord.Gear pump is the first run, or long-term idle before using, had better under the condition of no load or small load to run one hour or so.If in the running-in stage in advance the abnormal temperature rise, leakage, vibration and noise, should machine inspection.High viscosity of the pump outlet pipe also shall set up relief valve or other protective device on the road, so that once the clogging pump export channels, can open the relief valve pressure relief.For high viscosity gear pump need positive &negative, import and export all needs to set up the line safety valve.

   高粘度齒輪泵的吸油管道内徑應足夠大，并避免狹窄通道或急劇拐彎、減少彎頭，去除不必要的閥門、附件，盡可能地降低泵的安裝高度，縮短吸油管道的長度，以減少壓力損失。管接頭等元件的密封要良好，以防止空氣侵入，從而控制氣穴與氣蝕的發生。止回閥與安全閥在齒輪泵的輸出管路上最好安裝一個止回閥。這樣在檢修泵及輸出管道時，系統中的(de)液體不會發生倒流。齒輪泵帶負荷停車時，亦可防止泵倒轉而在其輸出管道内産生局部真空。應當注意，出口止回閥不能裝反或出現卡死現象。高粘度泵的出口管路上還應當設置安全閥等保護裝置，這樣一旦泵的出口通道發生堵塞，就可以打開安全閥卸壓。安全閥可以與泵體或泵蓋鑄成一體，也可以單獨裝配。對于需要正反轉的高粘度齒輪泵，其進出口管路上均需設置安全閥。High viscosity gear pump oil suction pipe diameter should be large enough, and to avoid the narrow channel, or a sharp turn, reducing elbow, remove unnecessary valves, fittings, as much as possible to reduce the installation height of pump, shorten the length of the oil suction pipe, in order to reduce the pressure loss.Components, such as pipe joint sealed well, in order to prevent the air intrusion, thus control air-pocket and the occurrence of cavitation.Check valve and relief valve on the output of the gear pump tube had better install a check valve.In the overhaul pump and output pipe, the system of fluid backflow will not occur.Gear pump to stop loading machine, can be in the output pipe to prevent pump reverse, and create a partial vacuum.It should be noted that the outlet check valve cannot be installed backwards or stuck.High viscosity of the pump outlet pipe also shall set up relief valve or other protective device on the road, so that once the clogging pump export channels, can open the relief valve pressure relief.The relief valve can be cast and pump body and pump cover, also can separate assembly.For high viscosity gear pump need positive &negative, import and export all needs to set up the line safety valve.

   高粘度泵是輸送高粘度液體的齒輪泵，應做到在較低的功耗、較少的洩漏、較大的(de)壓力下輸出最多的流量。在确定所要輸送的介質時，應該嚴格遵循産品說明書上的規定，盡量使用廠家推薦的流體介質，并注意考慮系統的工作溫度範圍。當希望在某一較寬的溫度範圍内使用時，輸送介質的粘度指數應該高些。輸送介質不僅是能量傳遞的中介，而且也是潤滑、密封及傳熱介質。液體粘度過高會增加内摩擦阻力，降低輸出功率，浪費能量，并産生過高的系統溫度.高粘度齒輪泵的出口管路上應當設置安全閥等保護裝置，這樣一旦泵的出口通道發生堵塞，就可以打開安全閥卸壓。對于需要正反轉的高粘度齒輪泵，其進出口管路上均需設置安全閥。High viscosity pump is conveying liquid with high viscosity gear pump, should be in lower power consumption, less leakage, under the pressure of large output the most traffic.When determining to conveying medium, we should strictly follow the provisions of the product manuals on use manufacturers recommend fluid as far as possible, and pay attention to consider the system operating temperature range.When you want to use in a wide temperature range, medium viscosity index should be higher.Medium is not only the energy transfer intermediary, but also lubrication, sealing and heat transfer medium.Liquid viscosity is too high will increase internal friction resistance, lower output power, waste of energy, and generate high temperature system. High viscosity gear pump outlet pipe shall set up relief valve or other protective device on the road, so once the clogging pump export channels, can open the relief valve pressure relief.For high viscosity gear pump need positive &negative, import and export all needs to set up the line safety valve.