3g100×4gr46w21立挂式三螺杆泵 壓力:4mpa,流量:72.36m3/h,配電機:y315

●3g三螺杆泵性能:

　　用來輸送溫度≤150℃、粘度3-760cst、不含固體顆粒、無腐蝕性、具有潤滑性能的介質。适用壓力範圍：0.6-2.5mpa;适用流量範圍：0.6-123m3/h。主要應用于燃油輸送、液壓工程、船舶工程，石化及其他工業。used to transfer temperature 150 ℃, the viscosity of 3 or less - 760 cst, not containing solid particles,non-corrosive, has the lubrication performance of the medium.apply pressure range: 0.6 to 2.5 mpa;applicable flow range: 0.6-123 m3 / h.mainly used in the fuel transfer, hydraulic engineering, marine engineering, petrochemical and other industries.

　　●3g三螺杆泵應用範圍:

　　1、介質為直線連續輸送、無攪拌、無脈動。2、振動小，噪音低。3、壓力高、效率高。4、結構簡單、拆裝方便。5、體積小，重量輕。6、磨損輕微，壽命長。application scope: 1, medium for linear continuous transmission, without stirring, without pulsation.2, small vibration, low noise.3, high pressure and high efficiency.4, simple structure, convenient tear open outfit.5, small volume, light weight.6, wear light, long service life.

　　●3g三螺杆泵工作原理:

　　3g型三螺杆泵是轉子型容積泵，适于輸送各種不含固體顆粒，無腐蝕性油類及類似油的潤滑性液體、輸送液體粘度2~760mm2/s，溫度不超過80℃, 超過80℃可用高溫泵3gw型。3 g type is three screw pump rotor type positive displacement pump, is suitable for conveying various not containing solid particles, non-corrosive oil lubricity and similar oil liquid, conveying liquid viscosity was 2 to 760 / s, temperature not over 80 ℃, more than 80 ℃ high temperature pump available 3 gw type.

    3g型三螺杆具有多種結構，一般小流量泵襯套和泵體合為一個，可以卧式和立式安裝。進油口方向可相隔90°任意安裝，軸封多數為機構密封。中等流量以上泵，襯套為一個單獨的零件固定于泵體内，螺杆軸端裝有平衡環以液力平衡其軸向力。一般結構為卧式。進油口方向亦可以相隔90°任意安裝。改變泵體後可制成立式。軸封根據情況有機械密封和軟填料密封兩種結構。three screw with multiple structure of 3 g, general small flow pump bushings and pump body into one, can be installed in a horizontal and vertical.oil inlet direction can be 90 ° apart any installation, most of the shaft sealing seal for your organization.the medium flow in pump, bushing as a separate component fixed in the pump body, screw shaft end is equipped with the gimbal ring to hydraulic balance the axial force.the general structure is horizontal.inlet direction also can be 90 ° apart any installation.after the change of pump body can be made into vertical.depending on the situation of the shaft sealing with mechanical seal and soft packing seal two structures.

    3g型三螺杆泵軸伸支承較小，應由原動機經彈性聯軸器直接驅動，不得用皮帶輪等會産生額外徑向力較大的傳動方式傳動。3 g type three-screw pump shaft and bearing is small, should be driven by a prime mover directly by the elastic coupling, shall not be used pulley will produce additional radial force large transmission way.

　　●3g三螺杆泵輸送各種油類時應注意事項：when conveying various oil matters should be paid attention to:

    1、輸送40~150mm2/s的油類最合适，允許按泵的(de)最高工作壓力使用。2、輸送40mm2/s以下的油類，為保證泵的流量及壽命應降壓使用。3、輸送150mm2/s以上的油類，且進油管道過長，彎頭過多，泵工作時如産生噪音或振動現象，則應考慮更換低一級轉速的(de)電機運轉或縮短吸入管道，減少彎頭。1, delivery was 40 ~ 150 / s best oils, permitted to use according to the maximum working pressure of pump.2, transmission oil, under 40 was/s in order to ensure the pump flow and life should be used antihypertensive.3, transmission of more than 150 was/s oils, and the oil inlet pipe is too long, too much bend, such as noise or vibration phenomenon when the pump work, should consider to replace the low level of rotational speed of motor operation or shorten the suction pipe, reducing elbow.

　　 ●3g型三螺杆泵安裝要求:3 g type three-screw pump installation requirements:

     1、安裝前應檢查泵的油封是否良好，并檢查泵在運輸中是否損壞，可用手轉動聯軸器是否有卡勁現象，如有則應拆泵進行清洗，修理和校正。1, before installation should check whether the oil seal of the pump is good, and check the pump is damaged in transportation, turn the coupling usable hand card trouble phenomenon, if there is any should tear open pump for cleaning, repair and calibration.2、安裝泵的進油和排油管道時，其管徑不得小于泵的進油和出油口口徑，進油管道不得過長，彎頭不得過多，否則将影響泵的(de)工作狀态。2, installation of pump suction and discharge of oil pipe, the pipe diameter shall not be less than the oil inlet of the pump and the oil outlet diameter, inlet pipe shall not be too long, elbow shall not too much, otherwise will affect the pump working condition.3、當有兩台以上的泵安裝在同一條主管線上，為便于泵的(de)啟動，在近泵的排油管上必須安裝逆止閥。3, when more than two head of pump installed in the same line, to facilitate pump start-up, in close to the oil drain pump must be installed on a non-return valve.4、對于在較高溫度（指60℃以上）下輸送粘度大的油類（如：重油）的備用泵，必須是熱備用泵，否則泵在低溫下啟動會造成電機過載或泵損壞。（建議在靠近泵的排油管上的逆止閥旁，并聯安裝一個小回流閥，對備用泵可微啟回流閥，使泵緩慢逆轉，其逆轉速≤100轉/分，使部分熱油經常流過泵内，達到泵熱備用目的）。4, for under high temperature (above 60 ℃) conveying the viscosity of oil (such as: heavy oil) of the standby pump, it must be hot standby pump, otherwise the pump at low temperature can cause the damage of motor overload or pump.(suggest near the exhaust non-return valve on the tubing pump, a small return valve installed in parallel, differentiable and the backflow preventer to standby pump, the pump slow reversal, the reverse speed 100 r/min or less, often make some hot oil flows through the pump, to pump hot standby purposes).5、輸送介質内含有機械雜質。将嚴重影響泵的(de)運轉和降低使用壽命，因此在泵安裝前，必須仔細清除進油管内的焊渣，沙粒等雜質，并應在進油管道靠近泵處安裝濾器，濾器網孔大小，可根據工作情況及介質粘度确定。（一般可用40~80目網），過濾面積一般不得小于進油管橫截面積的20倍。5, mechanical impurity is contained within the transmission medium.will seriously affect the operation and reduce the service life of pump, so before the pump installation, must be carefully clean up the feed tube welding slag, impurities such as grains of sand, and shall be installed in the inlet pipe near the pump filter, filter mesh size, is decided according to the working condition and medium viscosity.available (40 ~ 80 mesh net), filter area generally shall not be less than 20 times into the cross-sectional area of the tubing 6、盡量在泵進油和排油口處的(de)螺紋孔上連接壓力表和真空表，以便于觀察泵的運轉狀态。6, as far as possible in the pump suction and discharge of oil on the threaded hole mouth connect pressure gauge and vacuum gauge, in order to observe the pump running state.7、原動機與泵的(de)轉軸必須在同一中心線上，可用直尺測隙規在聯軸器圓周上間隔90°處檢查。8、原動機與泵的(de)轉向必須一緻，嚴格禁止原動機驅動泵逆轉。電機接線時，應先脫開電機與泵的(de)聯軸器，對電機作試運轉。使其轉向與泵的轉向标志一緻。7, prime mover and the pump shaft must be in the same center line, available ruler feeler gauge in the coupling of the circumference of a circle by 90 ° in check.8, steering engine and pump must be consistent, strictly prohibited prime motor driven pump reversal.electrical wiring, should first release coupling of motor and pump, a test run on the motor.the steering pump and steering sign agreement.

　　 ●3g型三螺杆泵的使用

　 　1、泵啟動前，必須全開進油和排油閘閥。the use of 3 g type three-screw pump 1, before starting the pump, oil inlet must be fully open and oil discharge gate valve.2、首次啟動泵或再次使用長期封存的泵時，泵内無介質，應在泵的(de)進油腔灌注适量輸送介質，避免泵幹啟動。2, start the pump for the first time or again for a long time use of the pump, the pump inside without medium, should be in the inlet of the pump cavity perfusion amount transfer medium, avoid dry start pump 3、泵啟動後，應密切注意電流表，壓力表和真空表的數值，超出規定值時，應停泵找出原因後，再行啟動。3, the pump starts, should pay close attention to current meter, pressure gauge and vacuum gauge value, beyond the specified value, should stop pump after find out, start again.4、軸封處點滴洩露，應屬正常現象，當洩露量大量增加時，對軟填料密封應壓緊填料壓蓋，對機械密封應停泵修複後，再行啟動。4, shaft sealing drip leakage, should belong to the normal phenomenon, when the leak amount of increase, the soft packing seal should be compression packing gland, to pump mechanical seal shall be shutdown after repair, start again.5、用高溫蒸汽清掃管線時，應避免高溫蒸汽通過泵内。5, with high temperature steam cleaning pipeline, should avoid high temperature steam through the pump.6、如果泵長期不工作時，應進行油封，并定期檢查油封情況，必要時重新油封。6, if the pump is not working for a long time, should carry on the oil seal, and regularly check oil seal, oil seal again if necessary.●水電行業業績:

1.安徽省淮北發電廠

型号:3g60×4cr43w21, 壓力4.0mpa,流量13.2m3/h,配用電機22kw-4

     3g70×3cr43w2, 壓力1.0mpa,流量16.02m3/h,配用電機7.5kw-4

3g100×4gr46w21, 壓力:4mpa,流量:72.36m3/h,配電機:y315s1—4v1

2.湘潭發電有限責任公司

型号:3g85×4cr46w21, 壓力4.0mpa,流量43.2m3/h,配用電機75kw-4

     3g80×3cr44w2, 壓力1.0mpa,流量35.04m3/h,配用電機15kw-4

3.陝西渭河發電廠

型号:3g45×3c2r46w2, 壓力1.0mpa,流量6.72m3/h,配用電機4kw-4

3g70×4gr40w21, 壓力:4mpa,流量:19.08m3/h ,配電機:y200l—4b5

4.廣西岩灘水電廠

型号:3g90×3c2r46w2,壓力1.0mpa,流量54.72m3/h,配用電機30kw-4

     3g85×42r46w21, 壓力4.0mpa,流量43.2m3/h,配用電機75kw-4

5.陳村水力發電廠

型号: 3g45×4gr42w21, 壓力4.0mpa,流量11.1m3/h,配用電機18.5kw-4

      3g90×4gr46w11,壓力:4.0mpa,流量51.48m3/h,配用電機90kw-4

6.王快水電廠

型号: 3g55×4g40w11, 壓力1.0mpa,流量9.72m3/h,配用電機5.5kw-4

      3g60×4gr46w11,壓力1.0mpa,流量16.26m3/h,配用電機7.5kw-4

3g70×4gr46w21,流量:24.24m3/h,壓力:4mpa,配電機:y225s-4b5

7.張家界水電開發公司

型号: 3g85×4g46w11, 壓力1.0mpa,流量48m3/h,配用電機22kw-4

        3g100×4gr54w11,壓力1.0mpa,流量100.5m3/h,配用電機45kw-4

8賀龍水電廠

型号: 3g80×4g44w11, 壓力1.0mpa,流量35.58m3/h,配用電機15kw-4

      3g70×4gr54w11,壓力1.0mpa,流量33.66m3/h,配用電機15kw-4

3g55×4gr40w21, 壓力:4mpa,流量:9m3/h,配電機:y160l—4b5

9.魚潭水電廠

型号: 3g80×4g44w11, 壓力1.0mpa,流量35.58m3/h,配用電機15kw-4

      3g70×4gr54w11,壓力1.0mpa,流量33.66m3/h,配用電機15kw-4

10.陝西石泉水力發電廠

型号: 3g55×4g46w11, 壓力1.0mpa,流量12.18m3/h,配用電機5.5kw-4

      3g70×4gr54w11,壓力1.0mpa,流量33.66m3/h,配用電機15kw-4

11.湖南中加電站

型号：3g80×6cr44w21, 壓力:6.3mpa,流量:33.54m3/h,配電機:y280m-4v1

3g90×6cr46w21, 壓力:6.3mpa,流量:51.5m3/h,配電機:y315m-4v1

3g80×4gr38w21, 壓力:4mpa,流量:25.56m3/h,配電機:y225m—4b5

12.黑龍江蓮花電站

型号：3g45×4c2r4w21, 壓力:4mpa,流量:5.12m3/h,配電機:y160m—4b5

3g100×6cr38w21, 壓力:6.3mpa,流量:48.42m3/h,配電機:y315m-4v1

13.福建羊口電站

型号：3g60×4cr46w21,流量:15.18m3/h,配電機:y200l—4b5

     3g100×4cr38w21,壓力4.0mpa,流量48.42m3/h,配用電機90kw-4

14.廣西天湖電站

型号：3g80×4cr38w21,流量:25.56m3/h,壓力:4mpa,配電機:y225m—4b5

3g100×4cr38w21,流量:48.42m3/h,壓力:4mpa,配電機:y280m—4v1

15.河南三門峽電站

型号：3g90×4gr50w21,流量:54m3/h,壓力:4mpa,配電機:y280m—4v1

3g80×4gr40w21,流量:30.06m3/h,壓力:4mpa,配電機:y250m—4b5